Home Assistant

Numato USB GPIO Expander

The numato integration is the base for all related GPIO platforms of the Numato 32 Port USB GPIO expander:

The whole configuration of all Numato devices is located in the general setup of this integration. The following minimalistic example configures a couple of binary_sensor, switch and sensor ports for a single device with ID 0.

numato:
  devices:
    - id: 0
      binary_sensors:
        ports:
          2: Window Livingroom Open
          3: Window Livingroom Glassbreak
          4: Doorbell
      sensors:
        ports:
          1:
            name: Soil Moisture Ficus
      switches:
        ports:
          5: Relay Light Outdoor
          6: Relay Circulation Pump
          7: Door Opener

Configuration Variables

Looking for your configuration file?
discover list (Optional)

List of OS device files (/dev/…) to try during discovery

Default:

List of /dev/ttyACM0 .. /dev/ttyACM9

devices list Required

List of Numato 32 Port USB GPIO devices.

id integer Required

ID configured in the device (not the Linux device since this can change).

binary_sensors map

Configuration of ports for the binary_sensor platform

invert_logic boolean (Optional, default: false)

Whether to invert the logic, so a high voltage level is interpreted as false.

ports map Required

Map of port numbers to names.

port: name string Required

The port numbers and corresponding names.

sensors map

Configuration of ports for the sensor platform

ports map Required

Map of port numbers to ADC configurations.

port: adc_config map Required

The port number and corresponding ADC configuration.

name string Required

Name of the ADC sensor port.

source_range list (Optional, default: [0, 1024])

Range within the ADC’s resolution to map values from.

destination_range list (Optional, default: [0.0, 100.0])

Range to map values from the source range to in a linear fashion.

unit string (Optional, default: %)

Unit of the destination values.

switches map

Configuration of ports for the sensor platform

invert_logic boolean (Optional, default: false)

Whether to invert the logic, so a value of true leads to a low voltage level at the output.

ports map Required

Map of port numbers to names.

port: name string Required

The port numbers and corresponding names.

Binary Sensor

The numato binary_sensor platform allows you to operate the GPIOs of your Numato 32 port USB GPIO expander in binary input mode.

As the Numato devices do not have internal pull-up or pull-down circuitry, be careful not to destroy a port by creating a short circuit. Refer to the Numato documentation on how to connect a switch to an input port, for example.

Sensor

The numato sensor platform allows you to operate some GPIOs of your USB GPIO expander in analog input mode.

The Numato device has a number of built-in analog-digital-converters (ADCs) to convert a voltage level between VCC and GND into a 10-bit integer value. Read the IO Ports section for constraints on the ports to use.

By default, the ADC’s whole 10-bit range will be mapped to a float value between 0.0 and 1.0. Use the optional source_range to map from a specific range and the destination_range to specify the value range to represent the entity state.

Switch

The numato switch platform allows you to operate the GPIOs of your Numato 32 port USB GPIO expander in output mode.

IO Ports

The IO port numbers used in this configuration refer to the port numbers printed on the PCB. Note that the Sensor platform can be configured on ports 1-7 only. These are the only ports on the 32 port device equipped with an ADC.

For details about the GPIO layout, take a look at the Numato 32 GPIO documentation.

Device IDs

This integration uses an internal device ID to identify the device, which is not the Linux device path. The Linux device path (e.g., /dev/ttyACM0) can change, for example, when you disconnect and re-connect the device or if you connect the device to a different USB port.

The internal device ID is 0 by default. If you have only one device, you should not need to care about changing it. If you have multiple devices, their IDs are shown in the console log during startup of Home Assistant.

Configure the Device ID

Configure your Numato device’s ID with the following steps. Though you can use any terminal emulator to connect to and communicate with your device, the following steps are based on using GNU Screen. On a Debian or Ubuntu-based OS install Screen like sudo apt install screen.

  1. Plug in only the one device to assign an id to so it’ll get /dev/ttyACM0
  2. Wait a couple of seconds as your Linux OS may be trying to identify the device as a Modem right after plugging it in
  3. Run screen /dev/ttyACM0
  4. Type id get to see the current ID
  5. Type id set 00000005 and hit enter to assign ID 5
  6. Type id get to validate and expect 00000005 as a reply
  7. Quit screen with: Ctrl-a + \ and confirm with y

Note that during communication with the device the ID values are strictly 32 bit hexadecimal numbers (8 hex digits) with leading 0 padding.

Hint: It is a good practice to put sticky labels with the IDs onto the PCBs in order to avoid confusion of devices and their port configuration since this could easily destroy your device.

Numato devices used by Home Assistant are expected to be exclusive to Home Assistant and remain permanently connected.